We read every piece of feedback, and take your input very seriously.
To see all available qualifiers, see our documentation.
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
hi, I need the hardware to compile and run with idf version 5.xx i want o use IDF5.14 and IDF5.3x .
After selecting example project "D:\esp-idf-v5.3.X\examples\ethernet\basic"
idf.py set-target esp32 idf.py menuconfig
Selected following options
(Top) → Example Ethernet Configuration Espressif IoT Development Framework Configuration [*] Internal EMAC Ethernet PHY Device (RTL8201/SR8201) ---> (23) SMI MDC GPIO number (18) SMI MDIO GPIO number (-1) PHY Reset GPIO number (0) PHY Address [ ] SPI Ethernet
After building and flashing and in monitor i get following eth init "reset timeout errors"
E (2608) esp.emac: emac_esp32_init(426): reset timeout E (2608) esp_eth: esp_eth_driver_install(228): init mac failed E (2608) example_eth_init: eth_init_internal(100): Ethernet driver install failed
Tried to both phy address 0 and 1 and also -1 (autodetect) always gets
Did I miss any other settings to be set for this board to work with IDF projects .
-----Monitor errors ------
ets Jul 29 2019 12:21:46 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:7176 load:0x40078000,len:15564 ho 0 tail 12 room 4 load:0x40080400,len:4 0x40080400: _init at ??:? load:0x40080404,len:3904 entry 0x40080640 I (31) boot: ESP-IDF -128-NOTFOUND 2nd stage bootloader I (31) boot: compile time Sep 9 2024 12:12:02 I (31) boot: Multicore bootloader I (36) boot: chip revision: v3.1 I (40) boot.esp32: SPI Speed : 40MHz I (44) boot.esp32: SPI Mode : DIO I (49) boot.esp32: SPI Flash Size : 16MB I (54) boot: Enabling RNG early entropy source... I (59) boot: Partition Table: I (63) boot: ## Label Usage Type ST Offset Length I (70) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (77) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (85) boot: 2 factory factory app 00 00 00010000 00100000 I (92) boot: End of partition table I (97) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=12de8h ( 77288) map I (131) esp_image: segment 1: paddr=00022e10 vaddr=3ffb0000 size=02474h ( 9332) load I (135) esp_image: segment 2: paddr=0002528c vaddr=40080000 size=0ad8ch ( 44428) load I (155) esp_image: segment 3: paddr=00030020 vaddr=400d0020 size=310bch (200892) map I (224) esp_image: segment 4: paddr=000610e4 vaddr=4008ad8c size=02a98h ( 10904) load I (235) boot: Loaded app from partition at offset 0x10000 I (235) boot: Disabling RNG early entropy source... I (247) cpu_start: Multicore app I (256) cpu_start: Pro cpu start user code I (256) cpu_start: cpu freq: 160000000 Hz I (256) app_init: Application information: I (259) app_init: Project name: ethernet_basic I (264) app_init: App version: 1 I (268) app_init: Compile time: Sep 9 2024 12:55:34 I (274) app_init: ELF file SHA256: bf88a08c2... I (280) app_init: ESP-IDF: -128-NOTFOUND I (285) efuse_init: Min chip rev: v0.0 I (290) efuse_init: Max chip rev: v3.99 I (295) efuse_init: Chip rev: v3.1 I (300) heap_init: Initializing. RAM available for dynamic allocation: I (307) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM I (313) heap_init: At 3FFB3748 len 0002C8B8 (178 KiB): DRAM I (319) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM I (325) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM I (332) heap_init: At 4008D824 len 000127DC (73 KiB): IRAM I (340) spi_flash: detected chip: generic I (343) spi_flash: flash io: dio I (348) main_task: Started on CPU0 I (358) main_task: Calling app_main() W (358) eth_example: -----IDF5.3x-------Ethernet CHIP RTL8201 ADDR=00 RST_GPIO= -1 ------------- E (2608) esp.emac: emac_esp32_init(426): reset timeout E (2608) esp_eth: esp_eth_driver_install(228): init mac failed E (2608) example_eth_init: eth_init_internal(100): Ethernet driver install failed I (2618) gpio: GPIO[0]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2618) gpio: GPIO[18]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2628) gpio: GPIO[19]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2638) gpio: GPIO[21]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2648) gpio: GPIO[22]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2658) gpio: GPIO[23]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2668) gpio: GPIO[25]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2678) gpio: GPIO[26]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (2688) gpio: GPIO[27]| InputEn: 0| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 E (2698) example_eth_init: example_eth_init(260): internal Ethernet init failed ESP_ERROR_CHECK failed: esp_err_t 0xffffffff (ESP_FAIL) at 0x400d7e56 0x400d7e56: app_main at D:/ESP32-WorkspaceIDF53X/basic/main/ethernet_example_main.c:79 (discriminator 1) file: "./main/ethernet_example_main.c" line 79 func: app_main expression: example_eth_init(ð_handles, ð_port_cnt) abort() was called at PC 0x40086033 on core 0 0x40086033: _esp_error_check_failed at D:/esp-idf-v5.3.X/components/esp_system/esp_err.c:49 Backtrace: 0x400819aa:0x3ffb58d0 0x4008603d:0x3ffb58f0 0x4008c069:0x3ffb5910 0x40086033:0x3ffb5980 0x400d7e56:0x3ffb59b0 0x40100823:0x3ffb5a40 0x400869cd:0x3ffb5a70 0x400819aa: panic_abort at D:/esp-idf-v5.3.X/components/esp_system/panic.c:463 0x4008603d: esp_system_abort at D:/esp-idf-v5.3.X/components/esp_system/port/esp_system_chip.c:92 0x4008c069: abort at D:/esp-idf-v5.3.X/components/newlib/abort.c:38 0x40086033: _esp_error_check_failed at D:/esp-idf-v5.3.X/components/esp_system/esp_err.c:49 0x400d7e56: app_main at D:/ESP32-WorkspaceIDF53X/basic/main/ethernet_example_main.c:79 (discriminator 1) 0x40100823: main_task at D:/esp-idf-v5.3.X/components/freertos/app_startup.c:208 0x400869cd: vPortTaskWrapper at D:/esp-idf-v5.3.X/components/freertos/FreeRTOS-Kernel/portable/xtensa/port.c:134 ELF file SHA256: bf88a08c2 Rebooting...
The text was updated successfully, but these errors were encountered:
Also flashed the unit test firmware
LilyGO-T-ETH-Series-master\LilyGO-T-ETH-Series-master\firmware\T-ETH-Lite-ESP32-UnitTest.bin
The board is ok eth geta ip address on the network
ets Jul 29 2019 12:21:46 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:1184 load:0x40078000,len:13192 load:0x40080400,len:3028 0x40080400: _init at ??:? entry 0x400805e4 [ 965][E][sd_diskio.cpp:802] sdcard_mount(): f_mount failed: (3) The physical drive cannot work [ 1465][E][sd_diskio.cpp:126] sdSelectCard(): Select Failed SDCard MOUNT FAIL ETH Started ETH Connected ETH MAC: 24:DC:C3:07:D0:CB, IPv4: 192.168.1.90, FULL_DUPLEX, 100Mbps, GatewayIP:192.168.1.1 Got time adjustment from NTP! Monday, September 09 2024 09:38:14 ===========ETH============= [ 11399][E][ssl_client.cpp:37] _handle_error(): [start_ssl_client():273]: (-9984) X509 - Certificate verification failed, e.g. CRL, CA or signature check failed [ 11402][E][WiFiClientSecure.cpp:144] connect(): start_ssl_client: -9984 [HTTPS] GET... failed, error: connection refused ===========WiFi============= ETH Disconnected ETH Connected ETH MAC: 24:DC:C3:07:D0:CB, IPv4: 192.168.1.90, FULL_DUPLEX, 100Mbps, GatewayIP:192.168.1.1 scan done 32 networks found
Sorry, something went wrong.
This is ELite, not Lite, Lite I haven't had time to get it yet
No branches or pull requests
hi,
I need the hardware to compile and run with idf version 5.xx i want o use IDF5.14 and IDF5.3x .
After selecting example project "D:\esp-idf-v5.3.X\examples\ethernet\basic"
idf.py set-target esp32
idf.py menuconfig
Selected following options
(Top) → Example Ethernet Configuration Espressif IoT Development Framework Configuration
[*] Internal EMAC
Ethernet PHY Device (RTL8201/SR8201) --->
(23) SMI MDC GPIO number
(18) SMI MDIO GPIO number
(-1) PHY Reset GPIO number
(0) PHY Address
[ ] SPI Ethernet
After building and flashing and in monitor i get following eth init "reset timeout errors"
Tried to both phy address 0 and 1 and also -1 (autodetect) always gets
Did I miss any other settings to be set for this board to work with IDF projects .
-----Monitor errors ------
The text was updated successfully, but these errors were encountered: